PCB cleaning before Beläggning

PCB cleaning before Konform beläggning is a critical preparation step in Montering av kretskort och SMT-montering. It involves removing contaminants from the circuit board surface to ensure proper adhesion and long-term reliability of the coating.

Why PCB cleaning is important

Under Montering av kretskort, various residues can remain on the board, such as:

• Flux residues from soldering
• Dust and particles from the environment
• Oils or fingerprints from handling
• Ionic contaminants

If these contaminants are not removed, the Konform beläggning may not adhere properly, leading to:

• Delamination or peeling
• Reduced insulation performance
• Corrosion under the coating
• Electrical leakage or failure

Proper cleaning ensures the coating forms a uniform and reliable protective layer.

Common PCB cleaning methods

Solvent cleaning

Solvent cleaning uses chemical solvents to dissolve and remove contaminants.

• Fast and effective for flux removal
• Suitable for small to medium production in SMT-montering
• Requires proper handling and ventilation

Aqueous (water-based) cleaning

Aqueous cleaning uses water combined with detergents.

• Environmentally friendly option
• Effective for removing ionic contamination
• Requires rinsing and thorough drying

This method is widely used in modern Montering av kretskort lines.

Ultrasonic cleaning

Ultrasonic cleaning uses high-frequency sound waves in a liquid solution.

• Removes contaminants from hard-to-reach areas
• Ideal for complex and densely populated PCBs
• Used for high-reliability electronics

Manual cleaning

Manual cleaning is done using brushes, wipes, or swabs.

• Suitable for rework or small batches
• Low cost and flexible
• Depends on operator skill

Drying after cleaning

After cleaning, PCBs must be completely dry before applying Konform beläggning.

• Use hot air ovens or drying chambers
• Ensure no moisture is trapped under components

Moisture left on the board can cause corrosion and coating defects.

Cleanliness standards

To ensure quality in SMT-montering, cleanliness is often verified using:

• Ionic contamination testing (e.g., ROSE test)
• Visual inspection under magnification
• Surface insulation resistance (SIR) testing

These checks confirm the PCB is ready for coating.

Slutlig slutsats

PCB cleaning before Konform beläggning is essential to remove contaminants and ensure strong adhesion, electrical reliability, and long-term protection. In Montering av kretskort och SMT-montering, proper cleaning and drying directly determine the effectiveness of the coating and the overall performance of the electronic product.

Få en offert på Conformal Coating

Behöver du professionell support för konform beläggning? Skicka in dina krav och få ett svar inom 12 timmar.
Skicka oss dina krav och få ett snabbt svar från vårt ingenjörsteam.

✔ Svar 24 timmar om dygnet ✔ Teknisk support ✔ Små- och massproduktion

Aktivera JavaScript i din webbläsare för att fylla i detta formulär.

Namn

E-post *

WhatsAPP

Rekommenderat material

• Akryl (AR)
• Silikon (SR)
• Polyuretan (UR)
• UV-härdbar - UV
• Jag är inte säker / Behöver råd

Filuppladdning

Dra och släpp filer,, Välj filer att ladda upp Du kan ladda upp upp till 8-filer.

Komprimera alla Gerber-filer, Drill-filer och BOM till en enda ZIP- eller RAR-fil för snabbare bearbetning.

WhatsAPP Message upload

Meddelande

"Ange komponenter eller områden som INTE får beläggas (t.ex. kontakter, testpunkter)." Om du har specifika krav på beläggningsmaterial (t.ex. HumiSeal), vänligen ange det i meddelanderutan nedan.

Skicka in

Shenzhen Tengxinjie Electronics Co, Ltd.