Export Gerber files from Eagle

Exporting Gerber files from Autodesk Eagle is a key step before starting PCB Üretimi ve PCB Montajı. Gerber files contain all the necessary data for fabricating your PCB, including copper layers, solder mask, silkscreen, and drill information.

Below is a step-by-step guide to help you correctly generate Gerber files for SMT Montajı ve üretim.

Open your PCB design

Start by opening your completed board file (.brd) in Autodesk Eagle. Make sure your design is finalized and all components are properly placed and routed.

It’s recommended to run a Design Rule Check (DRC) before exporting to ensure there are no layout errors that could affect PCB Montajı.

PCB Montaj Teklifi Alın

Open the CAM processor

In the top menu, go to
File → CAM Processor

The CAM Processor is the tool used to generate Gerber files for PCB Üretimi. It allows you to select layers and configure output settings.

Load a CAM job file

Eagle usually includes default CAM job files.

Click File → Open → Job, then select a standard job such as:
gerber.cam

This will automatically load predefined settings for common Gerber outputs, suitable for most PCB Montajı gereklilikler.

Configure Gerber layers

Ensure the correct layers are selected for export. Typical layers include:

• Top Copper (Top)
• Bottom Copper (Bottom)
• Solder Mask Top/Bottom
• Silkscreen Top/Bottom
• Board Outline (Dimension layer)

İçin SMT Montajı, accurate solder mask and silkscreen layers are especially important.

Set output format

Make sure the output format is set correctly:

• Format: RS-274X (standard Gerber format)
• Units: mm or inch (match your design settings)
• Resolution: usually 2:5 or 2:6

These settings ensure compatibility with most PCB Üretimi suppliers.

Generate Gerber files

Click the Process Job button.

Eagle will generate a set of Gerber files, typically including:

• .GTL (Top Layer)
• .GBL (Bottom Layer)
• .GTS / .GBS (Solder Mask)
• .GTO / .GBO (Silkscreen)
• .GKO or .GML (Board Outline)

These files are essential for both fabrication and PCB Montajı.

Export drill files

Gerber files do not include drill data, so you must export it separately.

Go to:
File → CAM Processor → Drill data (Excellon format)

This file contains hole sizes and locations, which are critical for PCB Üretimi.

Verify Gerber files

Before sending files to your manufacturer, always verify them using a Gerber viewer.

Check that:

• All layers are aligned correctly
• Board outline is accurate
• No missing pads or traces
• Text and markings appear properly

This step helps prevent costly errors in PCB Montajı.

Package files for submission

Finally, compress all Gerber and drill files into a single ZIP archive.

Include:

• Gerber dosyaları
• Drill file
• Readme or notes (if needed)

You can now send this package to your PCB Üretimi veya PCB Montajı supplier for quotation and production.

Sonuç

Exporting Gerber files from Autodesk Eagle is a straightforward process when using the CAM Processor with the correct settings. Proper file preparation ensures smooth SMT Montajı, reduces manufacturing errors, and speeds up your project timeline.

PCB Montaj Teklifi Alın

Güvenilir bir PCB montaj çözümü mü arıyorsunuz? Teklifinizi şimdi istemek için aşağıya tıklayın.
SMT, DIP ve tam anahtar teslimi çözümler dahil olmak üzere profesyonel PCB montaj hizmetleri sunuyoruz.

NDA Mevcut ✔ 24 Saat İçinde Hızlı Teklif ✔ ISO Sertifikalı Fabrika ✔ Tek Noktadan PCB ve PCBA Hizmeti