Konform beläggning process steps

I Montering av kretskort och SMT-montering, den Konform beläggning process follows a series of controlled steps to ensure reliable protection against moisture, dust, chemicals, and environmental stress. Proper execution of each step is critical for coating performance and long-term durability.

Inspection before coating

Before applying Konform beläggning, the PCB must be carefully inspected.

• Check for solder defects, contamination, or damage
• Ensure all components are properly assembled
• Verify that the board meets quality standards

Any defects left before coating can become difficult to repair later in Montering av kretskort.

Cleaning the PCB

Cleaning is one of the most important steps in the Konform beläggning process.

• Remove flux residues, oils, dust, and ionic contaminants
• Use solvent cleaning, aqueous cleaning, or ultrasonic cleaning
• Ensure the surface is chemically clean for proper adhesion

Poor cleaning can lead to coating failure, delamination, or corrosion.

Drying and moisture removal

After cleaning, the PCB must be completely dry.

• Use ovens or air drying to remove residual moisture
• Prevent trapped moisture under the coating

This step is essential in SMT-montering to avoid long-term reliability issues.

Masking

Masking protects areas that should not be coated.

• Connectors, switches, test points, and sockets
• Use tapes, boots, or removable masks

Accurate masking ensures functionality is not affected after Konform beläggning.

Coating application

Den Konform beläggning is then applied using one of several methods:

• Spraybeläggning (manual or automated)
• Doppbeläggning
• Beläggning med pensel (for repair or low volume)
• Selektiv beläggning (automated precision)
• Vapor deposition (for parylene coatings)

The choice depends on production scale and product requirements in Montering av kretskort.

Curing

After application, the coating must be cured to form a protective layer.

• Air cure (common for acrylic)
• Heat cure (epoxy, polyurethane)
• UV cure (fast and efficient)
• Moisture cure (silicone coatings)

Proper curing ensures the coating achieves its mechanical and electrical properties.

Inspection and quality control

Once cured, the coating is inspected to ensure quality.

• Visual inspection under white or UV light
• Check for coverage, thickness, bubbles, or voids
• Verify no unwanted areas are coated

Automated inspection systems are often used in advanced SMT-montering lines.

Testing and validation

Final testing ensures the coated PCB meets performance requirements.

• Electrical testing
• Environmental testing (humidity, temperature cycling)
• Adhesion and thickness checks

This step confirms reliability in real-world operating conditions.

Slutlig slutsats

Den Konform beläggning process in Montering av kretskort och SMT-montering includes inspection, cleaning, drying, masking, coating application, curing, and final inspection. Each step plays a critical role in ensuring that the coating provides effective and long-lasting protection for electronic circuits.

Få en offert på Conformal Coating

Behöver du snabb behandling av projekt för konform beläggning? Skicka in din förfrågan idag.
Skicka oss dina krav och få ett snabbt svar från vårt ingenjörsteam.

✔ Svar 24 timmar om dygnet ✔ Teknisk support ✔ Små- och massproduktion

Aktivera JavaScript i din webbläsare för att fylla i detta formulär.

Namn

Rekommenderad uppladdningsfil

E-post *

WhatsAPP

Rekommenderat material

• Akryl (AR)
• Silikon (SR)
• Polyuretan (UR)
• UV-härdbar - UV
• Jag är inte säker / Behöver råd

Filuppladdning

Dra och släpp filer,, Välj filer att ladda upp Du kan ladda upp upp till 8-filer.

Komprimera alla Gerber-filer, Drill-filer och BOM till en enda ZIP- eller RAR-fil för snabbare bearbetning.

Meddelande

"Ange komponenter eller områden som INTE får beläggas (t.ex. kontakter, testpunkter)." Om du har specifika krav på beläggningsmaterial (t.ex. HumiSeal), vänligen ange det i meddelanderutan nedan.

Skicka in

Shenzhen Tengxinjie Electronics Co, Ltd.