Export Gerber Files from Altium Designer

Exporting Gerber files from Altium Designer is a key step in preparing your design for PCB 제조 그리고 PCB 어셈블리. These files ensure your board layout is correctly translated into fabrication data for SMT 어셈블리 그리고 턴키 PCB 어셈블리.

Below is a step-by-step guide to exporting Gerber files properly.

Step 1: Open Your PCB Project

Start by opening your completed PCB layout file (.PcbDoc) in Altium Designer.

Before exporting, make sure your design is finalized and has passed all design rule checks (DRC). This helps prevent errors during PCB Manufacturing.

PCB 어셈블리 견적 받기

Step 2: Open the Gerber Export Tool

Go to the top menu:

File → Fabrication Outputs → Gerber Files

This will open the Gerber setup window where you can configure export settings.

Step 3: Configure General Settings

In the “General” tab:

• Set Units (millimeters or inches, mm is recommended)
• 선택 Format (e.g., 2:5 or 2:6 precision)
• Select RS-274X format (industry standard)
• Enable Embedded apertures

These settings ensure compatibility with most PCB 제조 프로세스.

Step 4: Select Layers to Export

Switch to the “Layers” tab and select all required layers.

Typical layers include:

• Top Layer (Top Copper)
• Bottom Layer (Bottom Copper)
• Internal Layers (for multilayer PCBs)
• Top Solder Mask
• Bottom Solder Mask
• Top Silkscreen (Overlay)
• Bottom Silkscreen
• Board Outline (Mechanical Layer)

Selecting the correct layers is critical for accurate PCB 어셈블리 and fabrication.

Step 5: Configure Apertures and Advanced Settings

In the “Apertures” tab:

• 사용 Embedded apertures (RS-274X)

In advanced settings:

• Enable Plot Layers in correct order
• Mirror settings only if required (usually off for standard exports)

Step 6: Generate Gerber Files

Click OK to generate the Gerber files.

Altium will output a set of files, each representing a PCB layer. These files will be saved in your project’s output folder.

Step 7: Export NC Drill Files

Gerber files alone are not enough—you also need drill data.

Go to:

File → Fabrication Outputs → NC Drill Files

Configure:

• Units (same as Gerber)
• Format (match Gerber precision)

Export the drill file, which defines hole locations and sizes for PCB 제조.

Step 8: Verify Gerber Files

Before sending files for PCB 어셈블리, always verify them using a Gerber viewer (Altium has a built-in viewer or you can use third-party tools).

Check for:

• Missing layers
• Alignment issues
• Correct board outline
• Proper pad and mask openings

This step helps avoid costly errors in SMT 어셈블리 및 프로덕션.

Step 9: Prepare for Turnkey PCB Assembly

For 턴키 PCB 어셈블리, you will need to provide:

• 거버 파일
• NC 드릴 파일
• BOM(자재 명세서)
• Pick and place (centroid) file
• 조립 도면

A complete file package ensures smooth coordination between PCB Manufacturing and assembly.

Common Mistakes to Avoid

• Exporting in outdated Gerber formats (always use RS-274X)
• Forgetting solder mask or silkscreen layers
• Mismatched units between Gerber and drill files
• Missing board outline
• Not verifying files before submission

Avoiding these mistakes ensures a smoother manufacturing process.

결론

Exporting Gerber files from Altium Designer is a straightforward but critical step in PCB production. By correctly configuring settings, selecting the right layers, and verifying outputs, you can ensure high-quality results in PCB 제조, SMT 어셈블리, 및 턴키 PCB 어셈블리.

A well-prepared Gerber package minimizes errors, reduces delays, and helps deliver reliable electronic products.

PCB 어셈블리 견적 받기

전문가의 조언과 정확한 가격을 한 번에 확인하세요. 지금 바로 견적을 요청하세요.
당사는 SMT, DIP 및 전체 턴키 솔루션을 포함한 전문 PCB 조립 서비스를 제공합니다.

NDA 가능 ✔ 24시간 이내 빠른 견적 ✔ ISO 인증 공장 ✔ 원스톱 PCB 및 PCBA 서비스